DCOF Rating for Natural Stone: What the Numbers Mean

DCOF Rating for Natural Stone: What the Numbers Mean

A DCOF rating is the wet dynamic coefficient of friction of a hard surface: a number that shows how much grip a floor gives a moving foot when water is present. For natural stone, the benchmark most specifiers use is 0.42 or higher for level interior floors that will be walked on when wet. That number is a starting point, not a guarantee. Stone type, finish, slope, cleaning products and the room itself decide whether a marble, travertine or limestone floor is a good match for the space.

This guide explains what DCOF measures, which targets apply to bathrooms, showers, kitchens, patios and pool decks, how finish affects grip, and what documentation to expect on a project that needs a number.

Surfaces Galore
surfacesgalore.com
Choose Stone With Wet Areas in Mind
Explore natural stone tiles and finishes for bathrooms, kitchens, patios and pool decks, with options in marble, travertine and limestone.
Shop Now

TL;DR

  • DCOF measures the friction of a wet surface under a controlled test. Under ANSI A326.3, 0.42 is the benchmark for level interior floors walked on when wet.
  • Showers, pool decks and exterior walkways are usually held to a higher target: 0.60 under the NFSI B101.3-2022 recommendations.
  • Finish matters as much as stone type. Polished surfaces below 0.42 belong where floors stay dry. Honed, tumbled and textured finishes suit wet areas.
  • The number describes lab conditions. Grout joints, slope, soap residue and maintenance change how an installed floor performs.
  • Walls and backsplashes are not walked on, so DCOF is a floor question. Choose those surfaces for look and cleanability.

Table of Contents

What a DCOF rating actually measures

DCOF stands for dynamic coefficient of friction. It is the friction needed to keep a shoe or foot sliding once it is already moving across a surface. Static coefficient of friction (SCOF), the older measure, captures the force needed to start sliding. The Tile Council of North America (TCNA) explains that the two cannot be directly compared, which is why an old static figure on a spec sheet tells you little about a DCOF requirement.

The test is run on a machine called a tribometer. It drags a small rubber pad across the tile at a set speed over a wet surface. The water contains 0.05% sodium lauryl sulfate, a wetting agent that spreads the water into a thin film. TCNA notes the reason: real floors carry soap residue, and the wetting agent mimics the slippery conditions that result when water meets it.

The method began in ceramic tile standards (ANSI A137.1) and was extended to all hard flooring materials, stone included, in ANSI A326.3. A SENSO test report traces that history: A326.3 was published in 2017, added field-testing procedures, and was updated in 2021.

For stone, there is a wrinkle worth knowing. The Natural Stone Institute explains that after the older ASTM C1028 test method was withdrawn in 2014, stone suppliers and specifiers lacked a method to document surface safety. Its technical department then studied the ANSI DCOF method on stone and found the results encouraging for stone use, with density and finish influencing frictional properties. Today DCOF under A326.3 is the number most U.S. specifications ask for.

What 0.42 means, and what it does not

The figure you will see everywhere is 0.42. Under ANSI A326.3, a wet DCOF of 0.42 or greater is the threshold for hard flooring in level interior spaces expected to be walked on when wet with water. The same standard adds that such materials are not necessarily suitable for all projects: the specifier still has to consider use, traffic, contaminants, maintenance, wear and manufacturer guidelines.

Three practical readings follow:

  1. 0.42 or higher is the accepted mark for a level interior floor that may get wet, such as a bathroom or laundry room.
  2. Below 0.42 does not mean dangerous. The standard says such materials, polished surfaces included, should be installed only where the floor will be kept dry when walked upon and safe cleaning procedures are followed. A polished marble foyer or a dry living room fits that description.
  3. Above 0.42 does not make a floor safe everywhere. A ramp, a steam shower and a patio are different problems.

The standard also reminds readers that its values reflect friction under specific controlled conditions with a specific apparatus, with no claim of correlation to actual footwear or human walking. It adds that installed DCOF can change over time because of wear and contaminants, so periodic deep cleaning may be needed. Treat the number as a comparison tool between finishes, not a promise.

DCOF targets by area

A326.3 sorts hard flooring into five product-use categories, according to TCNA’s FAQ (updated August 1, 2025): Interior Dry, Interior Wet, Interior Wet Plus, Exterior Wet, and Oils/Greases. The Interior Dry and Interior Wet categories carry the 0.42 value, while the other three are declared by the manufacturer.

Five DCOF categories and their stated values

For spaces beyond a level indoor floor, the ANSI standard itself gives no binding limits. An informative note in the standard, as quoted in a SENSO test report, says it is generally accepted that Interior Wet Plus areas such as locker rooms and public showers should reach at least 0.50, and Exterior Wet and Oils/Greases areas at least 0.55, with drainage, surface structure, grout joints and intended use also considered.

A separate recommendation, NFSI B101.3-2022, is more specific. As summarized by the ANSI blog, it sets these wet DCOF levels:

Area Recommended wet DCOF
Level areas likely walked on when wet (lobbies, toilet facilities) 0.42 or higher
Wet areas with light or no footwear (pool decks, steam rooms, showers) 0.60 or higher
Exterior walkways and patios 0.60 or higher
Areas exposed to oil, grease or fat (garages, catering) 0.60 or higher
Inclined areas and ramps (stairs, ramps, loading bays) 0.65 or higher

The same summary says anything below 0.30 calls for professional intervention. Because the sources set slightly different lines for the same room, the number your project uses is whatever the specifier, local code or owner writes into the specification. When in doubt on a commercial job, ask the design professional of record.

Why finish changes everything

Two tiles cut from the same block can behave very differently on a wet floor, because DCOF responds to surface texture. That is why the finish is the first lever to pull, before you change the stone.

Here is how the common finishes line up for design purposes:

  • Polished: mirror gloss, the most dramatic look, and the finish most likely to measure under 0.42 when wet. Per the standard, it belongs in areas kept dry. Polished marble in a living room, entry or dry bathroom wall is a classic pairing.
  • Honed: a smooth matte surface with no gloss. It is a natural choice for bathroom floors and kitchens where you want the stone look with a softer surface.
  • Tumbled: edges and surface are softened by tumbling, which gives travertine and limestone the lived-in character many homeowners want. The slightly uneven surface suits bathrooms, patios and pool surrounds.
  • Textured finishes: brushed, flamed, bush-hammered and sandblasted surfaces create real tooth underfoot. They are the usual route for exterior walkways and wet zones where the target is 0.60 or higher.

Natural stone is not uniform, and the Natural Stone Institute points to density and finish as the factors that influence frictional properties. A dense, polished marble and an open-textured tumbled travertine will not give the same reading. Our natural stone finishes guide walks through how each finish looks and feels, and our piece on anti-slip stone treatments covers the options for adding traction to a surface you already love.

What happens after installation

The lab number is measured on a clean sample. Your floor lives in a different world, and four things move its performance.

Grout joints and layout. Joints sit in the walking path and change how the surface reads under a foot. This is why A326.3 includes field-testing procedures for installed floors.

Soap and cleaner residue. The test uses a wetting agent precisely because soap film is part of real bathrooms. Cleaners that leave a film build up a slick layer over time. Use stone-appropriate products, and see our guide to safe stone cleaners and the products to avoid.

Wear and re-polishing. The ANSI standard warns installed DCOF can change over time through wear and contaminants. Routine care keeps the surface consistent; our natural stone maintenance guide lays out a schedule.

Staining and sealing. A sealer protects the stone from moisture and stains, and it should be a type suited to the finish and location. Stains and etching also change how a surface looks and feels, so it helps to prevent stains on natural stone tile from the start.

For a broader introduction to how slip resistance is rated beyond DCOF, including R ratings and pendulum tests, see our flooring safety guide on slip resistance.

Room by room: choosing stone for the job

Bathroom floors

A level bathroom floor that gets wet is the textbook case for the 0.42 benchmark. Honed or tumbled marble, limestone and travertine tiles are the usual picks, and smaller formats or mosaics add grout lines that give extra grip. Our post on modern bathroom floor tile ideas that meet DCOF 0.42 shows how designers combine these with the look of the room.

Honed travertine mosaic bathroom floor

A polished marble tile can still be the star of a bathroom. Use it on walls, vanity surrounds and other areas nobody walks on, and keep a honed or tumbled stone on the floor.

Shower floors

Shower floors fall under the 0.60 recommendation in NFSI B101.3-2022, because bare feet, soap and water meet on a surface that is often sloped to the drain. Mosaics are popular here: the many grout joints add traction, and small pieces follow the slope. Pair the floor with textured or honed stone rather than polished.

Kitchens

Kitchen floors are usually dry but see spills, and the oil and grease category in NFSI B101.3-2022 sits at 0.60 or higher. For a home kitchen, a honed or tumbled limestone or travertine gives a warm, forgiving floor, while a polished stone works better as a backsplash. A backsplash is never walked on, so DCOF does not apply to it; choose it for color, veining and how easily it wipes clean.

Entryways, living areas and hallways

Dry interior floors do not need a wet DCOF. For flooring not intended to be walked on when wet, ANSI A326.3 asks for a dry DCOF of 0.42 or greater. That leaves room for polished marble in formal spaces, as long as the floor is kept dry. Entry floors in rainy or snowy regions need extra thought, since wet shoes bring water in. A honed finish is a safer pick there. For ideas that balance look and durability, see our durable stone flooring ideas.

Pool decks, coping and patios

Pool surrounds combine bare feet, standing water and sun, so they sit at the top of the wet-area range. TCNA’s 2022 materials note that the International Swimming Pool and Spa Code requires pool decks, ramps and coping to have a minimum wet DCOF of 0.42 when tested per A326.3-2017, with the 2024 revision expected to carry that forward. The same code, as summarized by Walkway Management, also accepts a P4 pendulum rating as an alternative, and local adoption controls which version applies to your site.

For design, textured tumbled travertine pavers and coping are a common answer. Because NFSI recommends 0.60 for pool decks and exterior walkways, pick a textured finish and confirm local requirements before ordering.

Commercial and hospitality floors

Hotel lobbies, restaurants and spas mix polished showpieces with wet zones. TCNA lists public showers, interior pool decks, locker rooms, steam rooms and front-of-house restaurant areas as examples for the Interior Wet Plus category. Use polished marble in lobbies where a maintenance plan keeps floors dry, and textured stone in the wet-use areas.

On U.S. commercial projects, OSHA’s rule at 29 CFR 1910.22 does not set a friction number. It requires floors to be kept clean, orderly and dry as far as reasonable. So when a project does need a figure, it normally comes through ANSI A326.3 and the project specification.

Documentation: what a DCOF report should show

On residential projects, a clear finish choice and good maintenance usually settle the question. On commercial and hospitality jobs, a specification may ask for a DCOF report in the submittals. Know what a proper one contains.

A SENSO floor test report offers a good model. It records the standard used (ANSI A326.3), the instrument (a BOT-3000E tribometer), the rubber slider, the 0.05% SLS solution, the room temperature and humidity, and the results for each tested area. In that example, three areas averaged wet DCOF values of 0.45, 0.43 and 0.43, 0.44 overall, with the validation-surface checks passing before and after testing.

When a design team needs a figure for a particular stone and finish, the Natural Stone Institute runs an ASTM standards test laboratory whose services include slip resistance testing per ANSI A326.3, alongside absorption, compressive strength, flexural strength, abrasion and freeze/thaw tests. Specifiers on larger jobs often plan this early, because a number needed for a submittal is easier to get before material is installed than after.

A short checklist for the design team:

  • Write the required DCOF and the test standard (ANSI A326.3) into the specification.
  • Name the finish in the specification, since finish drives the result.
  • Note the use category: interior wet, interior wet plus, exterior wet or oils and greases.
  • Record the cleaning products and maintenance schedule so the installed floor stays consistent with the report.
  • Check the local code version, since adoption varies.

DCOF compared with other slip ratings

You may meet other labels on product sheets, especially on imported material.

  • SCOF (static coefficient of friction): the older measure. TCNA says the familiar 0.60 SCOF figure was an outdated recommendation, withdrawn in 2004, and not an ADA requirement. It also says ASTM C1028 was affected by stiction on smooth or polished tiles, which is one reason the industry moved to DCOF.
  • R ratings (R9 to R13): a German ramp-test scale. It uses oiled ramps and a different method, so R values do not convert into DCOF.
  • P ratings (P1 to P5): a pendulum-based scale, referenced by the pool code noted above as an accepted alternative.

The TCNA guide adds that the BOT-3000 tribometer correlates more closely with the German ramp than other tribometers. Even so, do not convert between scales. Read each rating on its own terms, and ask which one your project, code or specifier uses.

A designer’s view on DCOF and natural stone

Most questions we hear about DCOF come down to one worry: will the stone I love be safe where I want to put it? The answer is nearly always yes, if the finish matches the room.

We import marble, travertine and limestone directly, and we sell premium-grade material only. That lets us focus on what the stone does best: character, depth and variation that manufactured surfaces cannot copy. A 0.42 benchmark does not stand in the way of that. It tells you to choose a honed, tumbled or textured finish for wet floors and to keep polished surfaces for dry ones, where they look their best.

Our advice to designers and homeowners is simple. Decide where the water goes before you decide on the finish. Put polished stone on walls, vanities, backsplashes and dry floors. Put honed, tumbled and textured stone on bathroom floors, shower floors, pool surrounds and patios. Let the specification state the number, and keep the cleaning routine consistent so the floor performs as it should.

If you are choosing between finishes, order samples. We ship them free, and holding tumbled travertine next to a polished marble tile tells you more in a minute than a spec sheet does.

John | Surfaces Galore

Choosing stone with us

Surfaces Galore is a direct importer and nationwide supplier of marble, travertine and limestone tiles, mosaics, moldings, pavers and pool coping. Our direct-import pricing comes from removing middlemen, and we sell premium, non-commercial-grade inventory with free sample shipping and custom project support. Browse marble tiles, mosaics, travertine tiles and more to compare finishes for your floors and wet areas.

Dolce Crema 18X18 Limestone

For a warm, softened floor, our Dolce Crema 18X18 limestone and Dore Reale Light 12X12 tumbled tile are good places to start. For a bright, polished look in dry spaces and walls, see the White Dolomite 12X24 polished tile. Trade buyers can ask us about custom orders and bulk quotes.

FAQ

Is a DCOF of 0.42 enough for a bathroom floor?

For a level interior bathroom floor that gets wet, 0.42 is the benchmark in ANSI A326.3. It is a minimum for that case, not a guarantee, and the specifier still weighs the stone, finish, grout, cleaning and use. Shower floors are usually held to the higher 0.60 recommendation from NFSI B101.3-2022.

Can polished marble be used where it gets wet?

The standard says materials that measure under 0.42 wet, polished surfaces included, should be installed only where the floor stays dry and safe cleaning procedures are followed. Polished marble suits dry floors, walls, vanities and backsplashes. For wet floors, a honed or tumbled finish is the better match.

Does a backsplash or wall tile need a DCOF rating?

No. DCOF describes friction underfoot, so it applies to walked-on floors, steps and ramps. For walls and backsplashes, choose stone for its look, finish and how easily it cleans.

How do I get a DCOF number for a specific stone and finish?

A specification on a commercial project will usually name the standard (ANSI A326.3) and the required value. A test laboratory can run the method on the stone and finish, and the Natural Stone Institute’s laboratory lists this among its services. The report should state the apparatus, solution, conditions and results per area.

Does DCOF change over time?

Yes, on an installed floor. The standard notes that wear and contaminants can change DCOF, and that periodic deep cleaning may be needed to maintain it. Using stone-safe cleaners that do not leave a film helps keep results steady.

Sources

This article is provided for general informational guidance only. Natural stone varies in color, veining, texture and performance. For installation, sealing, cleaning and maintenance, follow the product manufacturer’s instructions and consult a qualified installer or stone-care professional. Always test cleaning and sealing products in an inconspicuous area first. Surfaces Galore is not responsible for damage, discoloration, etching, staining, installation issues or other problems resulting from

Leave a comment

Back to top